Details
Single eureka the boss smart vac belt extended life belt for use on Eureka Ultra or Boss Smart Vac models 4800 series including 4870AT, 4870BT, 4870DT, 4870F, 4870G, 4870GZ, 4870GZX, 4870HZ, 4870HZX, 4870J, 4870K, 4870KE, 4870MZ, 4870PZ, 4870RZ, 4870SZ, 4870SZX, 4870T, 4872AT, 4872BT, 4874AT, 4874B, 4875A, 4880A, 4880BT, 4880D, 4885AT, 4885BT, 4880UZ
OEM Part Number:61110A , 61110C
Replaces part number 61110, Eureka SmartVac Belt, Ultra Smart Belt, 61110B, 61110B-12, 70040A, 70646a, 71367a, n0038 eu style r, 71367, 71367A, 71367B, M0006 EU Style R. Same as Walmart Durabelt Vacuum Belt, Eureka R # 65110A-6, 001592699, 71367A G0021 EU Style R
.
![]()
OEM Part Number:61110A , 61110C
Replaces part number 61110, Eureka SmartVac Belt, Ultra Smart Belt, 61110B, 61110B-12, 70040A, 70646a, 71367a, n0038 eu style r, 71367, 71367A, 71367B, M0006 EU Style R. Same as Walmart Durabelt Vacuum Belt, Eureka R # 65110A-6, 001592699, 71367A G0021 EU Style R
.
Eureka the boss smart vac belt replacement instructions
Step 1. Make sure the vacuum is unplugged.
Step 2. By pressing the handle release button/latch flatten the vacuum.
Step 3. Lay the vacuum down and turn it over on its front side the bottom plate's is fully visible.
Step 4. Using the Phillips screwdriver, remove the screws from the bottom plate
Step 5. Gently remove brush roll
Step 6. Remove the older belt.
Step 7. Place the new belt around motor steel shaft and then around brush roll's belt track
Step 8. Insert the roller back into the slides of the bottom housing. It is easier if you insert left side of brush roll before the right side
Step 9. Roll the brush roll by hand just to make sure it is seated properly and that the belt is placed correctly over the belt track, which is a slightly raised portion of the rollerbrush.
Step 10. Put the base plate back plate. Make sure that it is under the 4 little tabs. Screw it back using Phillips screwdriver.
Lift the vacuum to its upright position. Plug it and start vacuuming. Hope you liked our DIY text instructions on how to replace eureka the boss RR belt.
Here is a neat video on how to replace this belt from vacuumfreak95 at youtube.com
Step 1. Make sure the vacuum is unplugged.
Step 2. By pressing the handle release button/latch flatten the vacuum.
Step 3. Lay the vacuum down and turn it over on its front side the bottom plate's is fully visible.
Step 4. Using the Phillips screwdriver, remove the screws from the bottom plate
Step 5. Gently remove brush roll
Step 6. Remove the older belt.
Step 7. Place the new belt around motor steel shaft and then around brush roll's belt track
Step 8. Insert the roller back into the slides of the bottom housing. It is easier if you insert left side of brush roll before the right side
Step 9. Roll the brush roll by hand just to make sure it is seated properly and that the belt is placed correctly over the belt track, which is a slightly raised portion of the rollerbrush.
Step 10. Put the base plate back plate. Make sure that it is under the 4 little tabs. Screw it back using Phillips screwdriver.
Lift the vacuum to its upright position. Plug it and start vacuuming. Hope you liked our DIY text instructions on how to replace eureka the boss RR belt.
Here is a neat video on how to replace this belt from vacuumfreak95 at youtube.com
California residents see Prop 65 WARNINGS 
WARNING! This product contains a chemical know to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warning.ca.gov
WARNING! This product contains a chemical know to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warning.ca.gov- You can also find this product in:
Additional Information
| SKU | 61110A / 61110C |
|---|---|
| Brand | Eureka |
| Manufacturer | Eureka |
DOES THIS BELT FIT THE BOSS 4870
No answers yet.
Be the first to answer this question
Be the first to answer this question
