Similar Items
Details
Genuine Shark Navigator Filter Kit XFF80. These are washable and resuable filters. The thinner filter is made of felt and the thicker is foam filter.
Fits Following Shark Models
Shark Navigator NV60, NV6026
Shark Navigator NV70
Shark Navigator NV80
Shark Navigator NV90
Shark Navigator NV95
Shark Navigator UV420
Shark Navigator Professional Model NV80
Shark Navigator Professional Model NV70
Shark Navigator Professional Model UV420
Shark Navigator Professional Model NVC80C
Quantity - 1 Foam and 1 Felt Filter
Part no # XFF80, EU-18001
.
Fits Following Shark Models
Shark Navigator NV60, NV6026
Shark Navigator NV70
Shark Navigator NV80
Shark Navigator NV90
Shark Navigator NV95
Shark Navigator UV420
Shark Navigator Professional Model NV80
Shark Navigator Professional Model NV70
Shark Navigator Professional Model UV420
Shark Navigator Professional Model NVC80C
Quantity - 1 Foam and 1 Felt Filter
Part no # XFF80, EU-18001
.
How to change XHF80 Filter
To clean the post-motor HEPA filter:
1 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum.
2 Take out the HEPA filter by pulling it straight out.
3 Replace it with the XHF80 filter you just bought at EZvacuum.com.
4 After every 3-4 vacuum runs, tap the HEPA filter gently to loosen dirt and debris.
DO NOT put the HEPA filter in the washing machine or dishwasher.
7 Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place.
To clean the pre-motor filters:
1 Remove the dust cup.
2 Pull the 2 filters out from the top of the motor base.
3 Replace the filter set XFF80 you just bought at EZvacuum.com.
DO NOT put the filters in the washing machine or dishwasher.
4 After everyt 3-4 vacuum runs, you may wash the filter under lukewarm water. Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.
5 Place the felt filter in first, then the foam filter.
6 Replace the dust cup
To clean the post-motor HEPA filter:
1 Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum.
2 Take out the HEPA filter by pulling it straight out.
3 Replace it with the XHF80 filter you just bought at EZvacuum.com.
4 After every 3-4 vacuum runs, tap the HEPA filter gently to loosen dirt and debris.
DO NOT put the HEPA filter in the washing machine or dishwasher.
7 Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place.
To clean the pre-motor filters:
1 Remove the dust cup.
2 Pull the 2 filters out from the top of the motor base.
3 Replace the filter set XFF80 you just bought at EZvacuum.com.
DO NOT put the filters in the washing machine or dishwasher.
4 After everyt 3-4 vacuum runs, you may wash the filter under lukewarm water. Squeeze out excess water and let air-dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.
5 Place the felt filter in first, then the foam filter.
6 Replace the dust cup
California residents see Prop 65 WARNINGS WARNING! This product contains a chemical know to the State of California to cause cancer, birth defects or other reproductive harm. For more information, go to www.P65Warning.ca.gov
- You can also find this product in:
Additional Information
SKU | XFF80 |
---|---|
Brand | Euro Pro |
Manufacturer | EuroPro |